IA 9 - Configuration guides
Knowledge base 222. Setting a Static IP address to the Identity Access PC
In some cases it may be required to connect an iNet controller to a PC without any network infrastructure. To make this possible the iNet controller can be reset to an IP Address of 10.0.1.230 by holding the reset button for 30 seconds. The PC also ...
Knowledge base 221: Identity Access Client Installation
If Identity Access (Client) software is to be installed and the Microsoft Windows firewall or other hardware/software providers firewall system is in use on the Identity Access (IA Server) PC then configuration to allow access is required. Once these ...
Knowledge base 220: Identity Access Pre-Installation Checks
To ensure that your software installs correctly, it is important to run through the following pre-installation checks. 1. Temporarily disable your antivirus for the duration of the installation. Due to the amount of Anti-Virus packages, we cannot ...
Knowledge base 219: Issuing HID Mobile Access credentials within Identity Access 9
1. From the menu bar, select Management > Employees/Visitors/Contractors depending on the type of user - 2. Click the green plus symbol. 3, Type the users 'First Name’ & Last Name’ and add the user to a group. Leave the Primary Token Number blank. 4. ...
Knowledge base 216: iNet IP Utility
The iNet IP Utility has been designed to make the setup of iNet's onto your customers network as simple as possible. The tool gives the ability to setup your controllers to static addresses, without the need to only plug 1 iNet onto the network at ...
Knowledge base 211: Lockdowns in Identity Access 9
Within Identity Access V9 it is possible to configure 2 different lockdown levels. Lockdown Level 1 is designed to shut down any access into a building/area of the building, however all request to exit buttons still operate as normal, this means that ...
Knowledge base 210: IDEMIA Enforced Security and Identity Access
IDEMIA have added a new feature to their biometric reader products called Enforced security, this turns on TLS 1.2 (Transport Layer Security) by default from the factory. Enforced Security will be present in products fitted with the following ...
Knowledge base 207: Identity Access Removed or Lost without backups
If the PC holding Identity Access software has failed and no external backup is available, then a reinstallation and recommission of the system will be required. A site survey may be required to ensure the system is setup as it was previously. Some ...
Knowledge base 203: Manually Installing SQL Server Express 2022
This article will guide you through the process of installing SQL Server Express 2022 manually and setting this up to work for an Identity Access instance. Requirements - Unrestricted Internet Access PC Administrator Privileges All Windows Updates ...
Knowledge base 202: Elevator Controls in Identity Access 9
In this guide you will learn how to setup elevator control in Identity Access 9. Setting up an elevator in Identity Access is very easy and enables you to control who has access to certain floors in a building up to 64 floors per controller. In order ...
Knowledge base 201: Moving Identity Access
Checking your Identity Access License When moving Identity Access from one machine to another it is important to check if the current Identity Access server has a Professional or Enterprise license and what version the software is currently running. ...
Knowledge base 199: Locating facility codes using Identity Access
It's not always clear which facility code has been encoded onto a card, but using Identity access you are able to locate this information very easily by following the steps below. Requirements: An iNet door controller configured for facility codes. ...
Knowledge base 195: Backup Tool in Identity Access 9
This article will explain how to backup and restore the database using the build-in Backup Tool in Identity Access V9 1. Before you can use the Backup Tool from the software, we need to specify the destination of the backup and where we want to store ...
Knowledge base 196: Setting up Aperio locks with Identity Access 9
This KB explains how to setup Aperio wireless locks and handles with the Identity Access software. Requirements: Aperio USB Radio Dongle Aperio Programming Application software Aperio Installation Key Aperio AH30 (Gen5) Hub Aperio Wireless handle or ...
Knowledge base 185: HID Mobile Access with Identity Access 9
Based on Identity Access Version 9.1.49 *Note- Before following this guide you must already have an HID Mobile Access Origo portal with some available mobile credentials, you must also have explained to your Android/iOS users how to download the ‘HID ...
Knowledge base 177: Card + Pin (Dual Authentication) within Identity Access 9
This knowledge base explains how to configure Identity Access V9 for Card and Pin, otherwise known as Dual Authentication. It's important the reader is used with the default 4-bit burst output and that the reader has not been flashed to output the ...
Knowledge base 176: Identity Access 9 & HID OSDP guide
This is a comprehensive guide which will explain how to install and configure OSDP V1 readers with an iNet controller. Requirements: Identity Access iNet Controller HID Reader – OSDP and Bluetooth compatible iPhone or Android Device – requires an ...
Knowledge base 172: Hikvision cameras in Identity Access 9 - Setup parameters
For setting up ONVIF CCTV streaming cameras under the IA Camera Setup page, please use the following URL, remember to change the IP, username, password and remove the chevrons <> - rtsp://<IP ...
Knowledge base 159: Importing Users via a CSV file into Identity Access 9
It's possible to import large numbers of employees, visitors or contractors into Identity access using the Tools menu and a CSV file. A sample CSV file has been attached to the end of this bulletin. 1. Once the CSV file has been created log into ...
Knowledge base 158: Time and Attendance (T&A) in Identity Access 9
Time and attendance can be enabled on any given reader within Identity Access. When an event happens on the reader it will be logged within the Time and Attendance reporting section of Identity Access. Doors with Contacts / Monitored Locks will ...
Knowledge base 149: ANPR cameras in Identity Access 9
Within Identity Access it is possible to integrate an ANPR camera to operate a barrier. This makes the integration of an ANPR camera seamless for an end user as reporting and adding of new number plates is in the same User Interface as their access ...
Knowledge base 181: HID Asure ID Software with Identity Access 9
Controlsoft Identity Access 9 install includes a copy of HID Asure ID® 7. This is an ideal choice for organizations looking for affordable and easy-to-use photo ID card software with direct integration with the Controlsoft Identity Access database. ...
Knowledge base 136: Changing a Downstream (RS-485) iNet into a Master iNet.
This document explains how to change an iNet door controller from being on the RS-485 bus into a Master controller. In the following screenshots, the downstream iNet with bus address #1 on the “Ground Floor” Master will be changed to a Master called ...